The Speed Turtle 2.0 Easy Flash Module is a small, easy to use vehicle exterior light flasher. The Speed Turtle 2.0 plugs into your vehicle's OBD-II port and will make select factory lights flash in a variety of flash patterns. The system is easily installed in minutes and is a true plug and play solution for most vehicles. The Speed Turtle module will not damage the vehicle and can be removed at any time and you can also install in another vehicle without repairing or replacing vehicle components. With the included software you can program the module to change patterns, park mode flashing and update firmware as updates become available.
What's in the Box:
- (1) Speed Turtle 2.0 Easy Flash Module
- (1) Toggle Switch OR (1) Voltage Input (Choose at checkout)
- 6' Micro USB Cable
- Zip Ties
- Installs directly into your vehicle's OBD-II port.
- Double sided tape allows you to stick the toggle switch directly to your dash
- 10 unique flash patterns
- Park mode allows you to change patterns or disable specific lights when in park.
- Two switch inputs as well as the ability to activate the module using pre-existing vehicle buttons or controllers
- Included software allows you to program which do and do not flash
- If your vehicle is equipped with these lights, the Speed Turtle 2.0 can flash:
- Front Low Beams
- Front High Beams
- Front Turn Signals
- Front Fog Lamps
- Front LED Accents
- Rear Turn Signals
- Rear Stop Lamps
- Third / Center Mounted Brake Lamp
- Reverse Lamps
- Rear LED Accents
- Pickup Bed Lamp
This harness provides a simple ON/OFF toggle switch with adhesive backing. There are two internal LEDs to the toggle switch with green indicating the switch is ON and orange indicating the switch is OFF. While this is the simplest of the two harnesses to install, it only provides one of the two possible switch inputs. The toggle switch harness is connected to Input 1 on the module.
This harness provides two ‘flying lead’ input wires. Each wire will accept a 5 – 17 volt input signal from a switch or light controller of your choice. The white wire corresponds to Input 1 and the green wire corresponds to Input 2.
|Chevy Silverado 1500||2007-2016|
|Chevy Silverado 2500||2007-2016|
|Chevy Silverado 3500||2007-2016|
|GMC Sierra 1500||2007-2016|
|GMC Sierra 2500||2007-2016|
|GMC Sierra 3500||2007-2016|
**Software not compatible with Mac Computers
Speed Turtle Flasher Demo: What You Need to Know About Your Speed Turtle
The Speed Turtle 2.0 Easy Flash Module is a small, easy to use...
Speed Turtle 2.0 How It Works
Wondering how the Speed Turtle 2.0 Flasher works? Check out th...
Speed Turtle 2.0 Flash Module in a Dodge Charger Hellcat Demo
We recently installed the Speed Turtle in a Dodge Charger Hell...
Speed Turtle 2.0 Flash Module in a Dodge Ram: Demo
This is how the Speed Turtle will look in your Ram 1500! Visi...
Speed Turtle 2.0 in a Silverado 1500
Check out this 2016 Chevrolet Silverado with the Speed Turtle ...
How to Update the Speed Turtle 2.0 Firmware
Need help updating your Speed Turtle Firmware? Watch this tuto...
Works great. The only reason I give it a 4 is because on the 2015 GMC Yukon both the high beam don't flash. I was sent a beta version of software to allow the low beams to flash.
GOOD PRODUCT WORKS WELL, WISHED IT WOULD HAVE SOME BETTER PATTERNS AND FASTER STROBES. ALSO THE INTERFACE TO CHANGE THE PATTERNS IS NOT THE EASIEST TO MESS WITH. BUT ALL IN ALL GOOD PRODUCT
Worked great for GMC 2013 very bright and noticeable
This device gets attention! I added it to the complement of lights already in place and am pleased. The only catch was that it went on a 2013 tahoe and the wiring of those lights prevents the ability to have back and forth flash patterns (i.e. R side fog light, then left side fog light) - It is just on/off so I was a bit disappointed about that, but otherwise the device is a great addition.
I bought this for my 2008 Suburban along with the ALDL splitter. I needed the splitter because I already use my ALDL connector for another plug-in. I also went with the toggle switch wire harness. I plugged everything in and routed the switch wire, turned it on and was impressed.. I'm using the flash pattern it came with and am happy with it. In my case it flashes the headlights, turn signals and fog lights in front. In back, it flashes the brake lights, backup lights and high mounted brake light. Very happy with my purchase.